WWT-100 welding line outstretched tester

WWT-100 welding line outstretched tester

WWP-100 welding line gibbous press tester

WWP-100 welding line gibbous press tester

FWG-d Flange width gauge

FWG-100-d, FWG-200-d, FWG-300-d Flange width gauge
Canneed FWG-d Flange width gauge is designed to measure the flange width of open ended cans.

The spring loaded can guides automatically position the can for fast, accurate, and repeatable measurements. Constructed of machined for corrosion resistance and long life.

The base plate is stainless steel to extend the wear life of the surface.

With the Mitutoyo 0.01mm Resolution Digital Indicator.

The gauges may be connected to a computer via a multiplexer.

CHG-300 Digital Can Height Gauges

CHG-300 Digital Can Height Gauges

CSS-100B Anti-noise seam saw

CSS-100B Anti-noise seam saw
The saw is provided with an anti-noise design and a special guide for 2- and 3-piece cans (65 mm dia.).

Special seam circular saw with double cut for can double seam inspections.

EPH-206 End Panel Holder-for Digital Enamel Rater

EPH-206 End Panel Holder-for Digital Enamel Rater

STR-100 Seam Stripper

The automatic STR-100 Seam Stripper is a sensible, affordable, teardown method to prepare the double seam teardown analysis.

One fast, safe teardown operation without damaging or distorting the cover hook.

Reduce teardown time for more frequent inspections.

Tooling quick change in few seconds. Available in size from 200 to 603 and for beverage, food, and aerosol cans.

Efficient cut and strip both aluminium and steel cans in a single motion.
10 seconds per can.

Eliminates the repetitious actions by hand .

STG-200-d Seam thickness gauge(digital)

The STG-200-d Seam thickness gauge can be used to measure Seam thickness.

With measure angle compensation. The center mesure point can be adjusted.

Cans can be auto- positoned in the center easily during measuring .

With the Mitutoyo 0.01mm Resolution Digital Indicator.

If you purchase the adapter and cable, the instrument can communicate with a computer.

ELT-100 Leak Tester for ends

The Canneed Leak Tester for End ELT-100 is designed for 2 ends.

The end is sealed in the compound area and Pressure is applied.

Leaking spots are made visible by revealing bubbles in the water bath.

Each end diameter or shape requires specially adjusted holders, which can be exchanged easily.

CSG-d Countersink Gauge

CANNEED CSG-d Countersink Gauge is a Digital gauges for measuring Countersink depth parameters

( the depth of beader of can). With the Mitutoyo 0.01mm Resolution Digital Indicator.
The gauges may be connected to a computer via a multiplexer.

CDG-100 End Curl Diameter Gauge

CDG-100 End Curl Diameter Gauge

ECH-d End Curl Height Gauge

ECH-d End Curl Height Gauge

VRM 2A Video Rivet monitor

The " Canneed VRM 2A Video Rivet monitor " is a Video camera system
to observe and evaluate the rivet profile images of ends.

Any end of varying diameter may be tested.

The end is cut throught the rivet by the low speed saw,
the rivet is positioned manually in front of the camera.

The rivet profile images display on the display.

CVG-100 Canners Vacuum Gauge

The Canneed "CVG-100 and CVG-200 Canner's Vacuum Gauge",
Used to measure the vacuum pressure of seamed cans.

The gauge is placed on top of the can and the piercing needle
is forced through the top of the can.

The rubber collar forms a temporary seal to allow for measurement.

KZJ-SST-2 Secure seal tester

The "Canneed KZJ-SST-2 Secure Seal Tester" is used to test seal integrity on the glass or plastic containers and cans.

The KZJ-SST-2 has been designed to address the special needs
of sealing cans and bottles that use aluminum roll-on, twist crowns, or plastic caps.

The KZJ-SST-2 operates with compressed air, nitrogen, or carbon dioxide. By detecting gas leakage, rather than liquid, the Secure Seal Tester gives more sensitive, accurate readings.

ALT-600 Leak Tester for Aerosol can

ALT-600 Leak Tester for Aerosol can

7001 Pressure tester

The "Canneed Model 7001 CO2 tester and Pressure Tester"
is used to test carbonated beverages for volumes of CO2 gas in glass/PET bottles and cans.

This instrument uses a pressure gauge (0-0.4Mpa or 0.6Mpa)

It is available in one and two litre sizes.

The sample is lifted easy to be pierced.

The 7001 CO2 tester will provide rapid and accurate determination
of CO2 gas volumes in alcoholic and non-alcoholic beverages
when used with the two pressure/temperature relationship charts
furnished with this instrument.

CLT-100 Leak Tester for can

The Canneed "CLT-100 Leak Tester for can" is used for checking
the permeability of 3-piece cans in a water bath.

The can is fixed by magnet disc plate and submerged into the water.

At the same time it is subjected to pressure and leaks are revealed by air bubbles. Test pressure 8 - 10 bar.

The test procedure is performed semi-automatically.

The tester is suitable for round 3-piece cans of max.
can diameter of 130 mm. The maximum can height is 300 mm.

CVG-200 Canners Vacuum Gauge

The Canneed "CVG-100 and CVG-200 Canner's Vacuum Gauge",
Used to measure the vacuum pressure of seamed cans.

The gauge is placed on top of the can and the piercing needle is forced through the top of the can.

The rubber collar forms a temporary seal to allow for measurement.

CVG-100 is designed for using near the product line, Consists of a 0 to 76cm Hg vacuum gauge, pierce point, and rubber collar.

Also available with dual scale to measure pressure to 15 psi. CVG-200 is designed for using in lab, Consists of a holder, a 0 to 76cm Hg vacuum gauge, pierce point, and rubber collar.

Also available with dual scale to measure pressure to 15 psi.

BPT-2 Bottle pressure tester

The "Canneed BPT-2 Bottle Ramp Pressure Tester" is an advanced testing instrument for pressure testing glass containers.

Pressure test containers to a predefined pressure point (proof testing) or to destruction. The BPT-2 Bottle Ramp Pressure Tester is ergonomically designed for ease of operation and maintenance, and fully conforms to international test requirements.

KZJ-BLT-01 Bottle lid tester

"Canneed KZJ-BLT-01 Tumbling Tester for crown closures"
The crown closures are tumbled over top for a certain time, causing abrasion. This test simulates the condition of unsorted storage during transport and feeding.

Advantages
Standardized abrasion test for crown closures

Standardized tumbling speed and Adjustable duration

SCO Sanitary Can Opener

SCO Sanitary Can Opener